Clarkson Comfort Zone Air Conditioning

Air conditioning Service Repair Installation Contractors for HVAC

Call 905-403-0545 for air conditioning service, repair and installations

Serving Mississauga Oakville and surrounding areas since 1989 this company knows your heating and air conditioning needs. Licensed by T S S A (Technical Standards and Safety Association) the governing body that control contractors dealing with the safety of gas installations and servicing in Canada. They have licensed HVAC service technicians on staff to repair and service your air conditioning and heating systems.

These contractors come highly recommended from residential home owners to commercial contractors.

Check some of their impressive Air conditioning and heating recommendations.

This contractor can install and service all your HVAC conditioning needs from two stage variable speed furnace installations to air conditioners with 2 speed fans with ozone friendly refrigerants. This company has fully licensed gas technicians on call for emergency service when your gas furnace or heating system decides to quit working or just needs cleaning. They service and repair all brands of furnaces and air conditioners from major manufactures.

Air conditioning brands and systems we repair service and install

American Standard, Airco, Airflo, AirPro, Bryant, Carrier, Coleman, Comfortaire, Comfortmaker, Ducane, Goodman, Heil, ICG, ICP, Intercity, Janitrol, Keeprite, LG, Olsen, Payne, Reznor, Rheem, Ruud, Trane, Weatherking and more

Service repair and installations of air conditioning and heating systems in

Mississauga Oakville Burlington Etobicoke Streetsville

Compare different Air conditioners

About Homepros Homepros Contractors Contact Homepros Join Homepros

<< HomePros.ca Home Page

Ajax Newcastle Brampton North York Brantford Oakville Burlington Pickering Caledon Port Hope East York Richmond hill Etobicoke Scarborough Georgetown Thornhill Maple Toronto Markham Unionville Milton Vaughan Mississauga Whitby Newmarket Woodbridge Newcastle
MISSISSAUGA, OAKVILLE, BURLINGTON, HAMILTON, LONDON, STONEY CREEK, ST. CATHERINES, NIAGARA FALLS, WATERLOO, KITCHENER, ANCASTER, DUNDAS, WATERDOWN, CARLISLE, FREELTON, GRIMSBY, GEORGETOWN, BRAMPTON, 905 AREAS, 416

BURNER FAILS TO IGNITE AND BLOWER FAILS TO RUN
CONDITION	SOLUTION
No electrical power to the furnace Current overload protector device defective or tripped (circuit breaker) Thermostat defective Thermostat wires broken Blower motor defective Blower relay defective Wire off motor Wire off relay Improper ground Thermostat located in high area	Reconnect or replace power source Reset circuit breaker Check amp draw from motor according to furnace's specification. Replace thermostat Replace wire or wires Relocate thermostat Replace motor Replace relay Reconnect wire Reconnect wire Clean and secure grounds

BLOWER RUNS BUT FAILS TO IGNITE
CONDITION	SOLUTION
Low voltage 12 volt polarity reversed Furnace grounding wires not secure Gas valve defective Gas pressure incorrect Limit switch defective or wire off Sail switch defective or wire off Burner orifice defective Combustion air wheel loose Burner head adjustment Exhaust blocked Air intake restricted Broken or loose wire Motor running slow	Correct Power Supply Correct polarity Clean and secure grounds established Replace valve or valve coil, depending on problem encountered Set pressure to a minimum of 11"W.C. with all appliances running (Replace regulator if not obtainable) Reconnect wire or replace Reconnect wire or replace Clean main burner orifice or replace. Reposition and tighten Reposition and tighten Adjust burner according to furnace specifications. Clean exhaust Clean air intake Replace or tighten Check voltage first If 12 VDC while running, replace motor
BLOWER SHUTS OFF AT SAME TIME BURNER SHUTS OFF.
CONDITION	SOLUTION
Faulty relay Thermostat wired wrong	Replace relay Correct wiring

BURNER CYCLING ON AND OFF - BLOWER RUNS CONTINUOUSLY WITH THERMOSTAT "ON"
CONDITION	SOLUTION
Restricted return air supply Restricted discharge duct system Defective limit switch Furnace over fired	Make sure return air meets furnace's minimum requirements. a. Make sure ducting meets furnace's minimum requirements b. Make sure there is no excess ducting or unnecessary bends c. Make sure any closeable registers are fully open and unrestricted Replace limit switch. Set gas pressure to a minimum of 11"W.C. with all appliances running. Replace regulator if not obtainable Also, check main burner orifice, it must comply with furnace's specifications

BLOWER VIBRATES OR IS NOISY
CONDITION	SOLUTION
Damaged blower wheel Motor shaft bent Loose motor Restricted discharge duct system	Replace blower wheel Replace motor Tighten motor mounting bracket a. Make sure ducting meets furnace's minimum requirements b. Make sure there is no excess ducting or unnecessary bends c. Make sure any closeable registers are fully open and unrestricted

PILOT FAILS TO IGNITE OR STAY LIT
CONDITION	SOLUTION
Plugged pilot orifice Electrode out of adjustment Pilot tube defective Piezo sparker defective Defective thermocouple Defective valve Vent kit not sealed MICA window missing Combustion air hose plugged or collapsed Water in propane Burner plate gasket or pilot not sealed	Clean or replace orifice Adjust electrode to furnace's specifications Replace tube Replace sparker Replace thermocouple Replace valve Seal vent where it meets the furnace. Replace MICA Replace combustion hose Add alcohol to the propane bottles. Replace gaskets

LAZY FLAME (yellow)
CONDITION	SOLUTION
High gas pressure Burner out of adjustment Combustion wheel installed backwards Air leakeage at gaskets Low voltage	Set pressure to a minimum of 11"W.C. with all appliances running Replace regulator if not obtainable Adjust burner according to furnace specification Reposition wheel and tighten Replace gaskets Correct power supply

FAN RUNS CONTINOUSLY WITH THERMOSTAT "OFF"
CONDITION	SOLUTION
Defective thermostat Shorted thermostat leads Defective relay	Replace thermostat Replace wire or wires Replace relay

INSUFFICIENT HEAT
CONDITION	SOLUTION
Furnace under fired	1. Set gas pressure to 11"W.C. with all appliances running. Also, check main burner orifice, it must comply with furnace's specifications 2. Check ducting and return air according to furnace's specifications